torephp.blogg.se - Asus router app wol wake on wan

Asus router app wol wake on wan how to#
Asus router app wol wake on wan Pc#
Asus router app wol wake on wan free#
Asus router app wol wake on wan mac#
Asus router app wol wake on wan windows#

You were right, I did say 7 in my initial post - I probably mixed them up during several tries.

Asus router app wol wake on wan windows#

To open Powershell press on the Windows Key and X at the same time. The final option on the page, Ping Specific Port using Powershell, does work without needing to reboot. You can just type your IP Address a space then the port number since you already have telnet running.įYI the "$" is just the prompt and is not part of a command. You can test that it is working by just typing Make sure you use an elevated command prompt when you type the command.

Once you get telnet installed it will have to reboot.

Asus router app wol wake on wan how to#

If you don't know how to open Control Panel. I just tested this (Option 1) and it works: Apparently Microsoft stopped making it a part of the default installation of Win 10 somewhere among the many updates but it is still available just not with sudo which is a Unix command. Thank you and hope we can make this work! I'll provide any other info or clarifications that are needed. I am not an expert, not even too much of a tech-savvy, I've done my best to describe what I've done but some confusions may have occurred.

Asus router app wol wake on wan Pc#

router connected via ethernet cable to the PC In the process I didn't pay attention to it, presumed it has no interference. if it matters, got a secondary network card, ASUS PCE-N53 on PCI-E card#2. PC - Asrock X99 Extreme 4 motherboard with onboard Intel I218-V

Asus router app wol wake on wan mac#

succesfully tested the magic package via a testing tool, with the PC turned on and set the app to "listen" (I'll post a link to the tool if it's needed) - I used my DDNS address for host (ip) address Port 7 MAC address - the one on the back of my router.

Asus router app wol wake on wan free#

configured a dynamic DNS through my router, by using the free asus service configured port forwarding to forward port UDP 7 to my network card ip range - 192.168.1.255 enabled magic packet options in both BIOS and network card properties (and it works, as I was able to start it with Anydesk) To be able to WOL through the internet, I've followed some steps described in a few other websites (I can post them if needed) - basically: I've managed to wake up my PC through LAN by using Anydesk however it only works if the other device is connected to the same local network (i mean wake up from shut-down state).

I've configured a remote acces through windows and also have an Anydesk account configured (just context). If you still need help leave a comment below and I’ll try to help.At my current job sometimes i have to work in remote places i have quite a large library of resources on my home PC that would be great to be accessible remotely. This whole guide might seem a bit complicated, but it’s really easy to set up if you follow these steps carefully,

Access the router interface, go to the WOL section and remotely start the PC you’ve configured earlier.

The computer you took with you on your vacation is now on the same local network as your own router.

Connect to that VPN using the external IP of the home router.

Configure a VPN network server on your own router.

I won’t go into details in this article, but it basically goes like this: Most likely you’ll want to turn on a computer remotely from the Internet to do some work, and that’s totally possible, even if you’re not on the same network with the router. When is WOL useful, you may ask? Well, if you’re in the other room and don’t feel like getting up from the couch to press the Power button. What If You Want to Turn On Remotely a Computer From the Internet? If you plan to access it remotely you’ll need to wait for it to completely boot up. Your computer will start up just like if you had pressed the Power button. Get The MAC Address of The Network Card Connected to The Router In my case, the NIC name is “Intel NIC 1000Mb” in the image below. If you didn’t rename it previously it will match the card name from Device Manager. On top of the page is a small schematic with your computer, a globe representing the Internet, and your network card linking them together. Open the Start menu and type Network status.Ģ. Note: you can configure all NICs to enable WoL, but only the one connected to the router will be able actually to wake up the computer.ġ. Find the Correct Network Card (NIC) Connected to the Routerĭo you have more than one network card, as I do? There’s an easy way to figure out which one you must configure for WOL.

You may also need to do a bit of detective work to figure out which network card is the correct one if you have more than one NICs. You now need to configure the router to wake up the correct computer. Your computer will wake up pretty much immediately after a shutdown, trust me. Note: If you don’t check the Magic Packet box the computer will wake up automatically when any data package is received.